zhengzhou , china[email protected]
Crusher Feed Size Product Size Capacity (ton/hr) Power Requirement Jaw Crusher 1.8 m 250 mm 1200 High Gyratory Crusher Same Same 4500 High Smooth Roll Crusher 12-75 mm 12-1 mm 350 Low Tooth Roll Crusher 500 mm Same 500 LowLeave Us Now
You can also send a message to us by this email [email protected], we will reply to you within 24 hours.Now tell us your need,there will be more favorable prices!
They depend on the feed characteristics and the crusher configuration. The feed material should be at least 20% smaller than the width of the feed open - ing. Arrangement drawing with fitting dimensions and loads on request. Large feed opening 3,080 x 1,675 mm Jaw gyratory crusher …
Gyratory Crushers - Mineral Processing Metallurgy. Feb 17, 2016 Primary gyratory crushers are designated by two numbers. These are the size of the feed opening (in inches) and the diameter of the mantle at its base (in inches).
The Effect of Choke Feeding a Gyratory Crusher on Throughput and Product Size. J -F Dupont (1), J McMullen (1) and D Rose (2) 49th Annual Canadian Minerals Processors Conference, Ottawa, Canada, 2017 ABSTRACT The Detour Lake mine is located 200 km northeast of Timmins, Ontario, Canada.
Apr 20, 2019 Feeding and discharging size Compared with the jaw crusher, the feeding size of the rotary crusher is larger, the discharging size is smaller and more uniform, and the content of needle-like particles in the discharging is less than 10%. the raw material can directly into the feed mouth without the need for a feeder.
The feed size of gyratory crusher varies from ____ a) 150-190 mm b) 200-800 mm c) 500-600 mm d) 100-150 mm Answer: a Clarification: The minimum acceptable feed in a gyratory crusher ranges from 150 to 900 mm and product ranges from 1 to 10 inches. 3. The capacity of a gyratory crusher is ____ a) 3000 T/hr b) 4000 T/hr
Aug 23, 2021 Difference Between Jaw Crusher and Gyratory Crusher : (i) It is a reciprocating machine. (i) It is a gyratory machine. (ii) Intermittent in action, i.e., discharge is discontinuous. (ii) Continuous in action, i.e., discharge is continuous. (iii) It is a primary crusher. It takes a feed of larger size. (iii) It is a secondary crusher.
The maximum feed size is 300 mm, and the discharge size is about 20-40 mm. The short head cone crusher can be used for tertiary or quaternary crushing (fine crushing). The maximum feed size is 120 mm, and the output size is 5-20 mm. There are three designs for standard head and end cone crusher: “coarse”, “medium” and “fine”.
It can directly feed materials to the gyratory crusher by multiple vehicles, so the production capacity is large (1500-9000 t/h), the unit energy consumption is small, and the work is stable. The noise is small. The crushed stone has uniform particle size and relatively few flakes. The disadvantages of the gyratory crusher are also obvious:
Another inventor, Philetus W. Gates, patented the first gyratory crusher in 1881. There were crushers patented before Whitney’s, but they never made it into production. Since the late 1800s, the size of crushers has greatly increased, but the engineering principles …
May 06, 2021 F80 feed size; Rock’s compressive strength; Required reduction ratio; A jaw crusher size is obtained by looking at its feed opening (gape) and length. As an example, a monster 7959 of 79″ x 59″ (2m x 1.5m) will have its fixed jaws 79″ apart where the feed enters on a 59″ wide set of liner plates.
Feb 17, 2016 Primary gyratory crushers are designated by two numbers. These are the size of the feed opening (in inches) and the diameter of the mantle at its base (in inches). A 60″~x~89″ crusher would have an opening dimension of 60 inches (152 cm) and a diameter across the base of the mantle of 89 inches (226 cm).
Feb 26, 2016 Following the curve down to the 1.5″ line, we find that 43% of the primary crusher output may be expected to pass this screen opening; 57% will be retained, which means that we must provide secondary crushing capacity to take care of 57 tons for each 100 tons fed to the primary crusher.
Oct 22, 2015 If the ore feed to any gyratory or jaw crusher consisted entirely of large cubes or spheres of a size that would just barely enter the crushing chamber, the crusher could not be expected to produce anything like its normal rated capacity because the upper part of the crusher could not shatter the large pieces enough to keep the rest of the crushing chamber busy. Such a condition is of course …
The TS gyratory crusher is distinguished from other gyratory crushers by its revolutionary design which allows major ... • ROM feed size up to 2,000 mm • Capabilities in excess of 12,000 mtph • Insensitive to clay and sticky materials • Pre-scalping of undersize not required
Jan 01, 2016 The feed size to a gyratory crusher is 2.54 cm and nearly uniform. The product analysis is given in column (2) in the table below. The power required to crush the feed was 500 kW. The clearance between the crusher head and cone was then reduced yielding a product whose size distribution was given in column (3) of the same table. Estimate 1.
5 rows The gyratory crusher has capacities starting from 1200 to above 5000 t/h. To have a feed opening ...